| １． |
Outline |
|
Main topics are as follows:
・Fundamentals of the drawing
・Projection
・Lines and characters
・Scaling
・Cross section
・Dimension, roughness, annotation
・Tolerance
・Drawing of typical machine elements (Flange, Screw, Coupling and Geared-transmission)
*The course constitutes by a lecture and a practice. First, students follow the lecture about the designing and drawing manner. Then, students start the practice by using the knowledge of previous lectures.
|
| ２． |
Objectives |
|
A practice of the basic mechanical drawing in accordance with JIS standard. The practice includes the designing of machine elements.
|
| ３． |
Grading Policy |
|
Final grade will be calculated according to drawing assignments (100%). To pass, students must earn at least 60 points out of 100.
|
| ４． |
Textbook and Reference |
|
機械工学入門シリーズ 要説 機械製図 (in Japanese), Third edition
Kiyoshi Onishi
Reko-gakusya
|
| ５． |
Requirements (Assignments) |
|
Will be introduced in the class.
|
| ６． |
Note |
|
This course will be taught in Japanese.
|
| ７． |
Schedule |
|
１. Guidance, Writing characters in the drawing
|
２. Drawing standard lines, Operation of the drafting machine
|
| ３. Drawing assignment #1, Flange |
| ４. Drawing assignment #2, Screw, Bolt, Nut |
| ５. Drawing assignment #3, Coupling 1 |
| ６. Drawing assignment #4, Coupling 2, Check assignments (#1~4) |
| ７. Practical assignment "Transmission" #1, Measuring and Sketching elements |
| ８. "Transmission" #2, Pulley and Gear |
| ９. "Transmission" #3, Body |
| 10. "Transmission" #4, Shaft |
| 11. "Transmission" #5, Flanges |
| 12. "Transmission" #6, Assembly (1) |
| 13. "Transmission" #7, Assembly (2) |
| 14. "Transmission" #8, Assembly (3) |
| 15. Check assignments (transmission) |
|
| １． |
Outline |
|
Main topics are as follows:
・Fundamentals of the drawing
・Projection
・Lines and characters
・Scaling
・Cross section
・Dimension, roughness, annotation
・Tolerance
・Drawing of typical machine elements (Flange, Screw, Coupling and Geared-transmission)
*The course constitutes by a lecture and a practice. First, students follow the lecture about the designing and drawing manner. Then, students start the practice by using the knowledge of previous lectures.
|
| ２． |
Objectives |
|
A practice of the basic mechanical drawing in accordance with JIS standard. The practice includes the designing of machine elements.
|
| ３． |
Grading Policy |
|
Final grade will be calculated according to drawing assignments (100%). To pass, students must earn at least 60 points out of 100.
|
| ４． |
Textbook and Reference |
|
機械工学入門シリーズ 要説 機械製図 (in Japanese), Third edition
Kiyoshi Onishi
Reko-gakusya
|
| ５． |
Requirements (Assignments) |
|
Will be introduced in the class.
|
| ６． |
Note |
|
This course will be taught in Japanese.
|
| ７． |
Schedule |
|
１. Guidance, Writing characters in the drawing
|
２. Drawing standard lines, Operation of the drafting machine
|
| ３. Drawing assignment #1, Flange |
| ４. Drawing assignment #2, Screw, Bolt, Nut |
| ５. Drawing assignment #3, Coupling 1 |
| ６. Drawing assignment #4, Coupling 2, Check assignments (#1~4) |
| ７. Practical assignment "Transmission" #1, Measuring and Sketching elements |
| ８. "Transmission" #2, Pulley and Gear |
| ９. "Transmission" #3, Body |
| 10. "Transmission" #4, Shaft |
| 11. "Transmission" #5, Flanges |
| 12. "Transmission" #6, Assembly (1) |
| 13. "Transmission" #7, Assembly (2) |
| 14. "Transmission" #8, Assembly (3) |
| 15. Check assignments (transmission) |
|
|