| １． |
Outline |
|
Understanding of Design and Drawing is deepened by studying and learning the basics of machine design, strength and stiffness of materials, and accuracy and precision of machines. Students will learn the design skills and methods for five basic machine elements, namely, screw, shaft, bearing, gear and spring, and exercise designing of them. By the end of the course, the design calculation and design drawings for the above five elements will be completed. In this course, and students perform a group work and students make a presentation of their solution for task in front of other students. Students can acquire the knowledge, skill and behavior for DP2 to DP4.
|
| ２． |
Objectives |
|
It's so important to have skill and knowledge of basic Design and Drawing if one is to pursue a career in Product Engineering (MONOZUKURI).
In this course, students will learn the basic design of machines, design concepts, material strength and stiffness, machine accuracy and precision, and international standards for machines. Another purpose of this course is to learn the design and drawing methods for five element components of machine, namely, screw, shaft, bearing, gear and spring. Objective of this course is acquiring the fundamental knowledge and skills for the Design and Drawing for Product Engineering. And students will have a presentation skill through this course. So, students can discuss about drawings based on their learning of this course.
|
| ３． |
Grading Policy |
|
Your final grade will be calculated according to the following process : Reports for tasks(30%) and submission of the calumniation report and drawings for final task(70%) on 14th & 15th classes. And students are required to attend classes over 2/3 of total classes in this course, in order to take part in the term-end examination.
|
| ４． |
Textbook and Reference |
|
Textbook:『Mechanical Design Method(the third Edition)』：Tadao Tsukada ;Morikita Pablishing Co., Ltd.
Reference book:『Main Theory Mechanical Drawing』：Kiyoshi Onishi;Ohmusha Pablishing Co., Ltd.
『Basic of Mechanical Design and Drawing(the second Edition)』; Surikogaku Pablishing Co., Ltd.
|
| ５． |
Requirements (Assignments) |
|
Students should study(1hr) watching and reading textbook and documents by LMS and they also should review(2hr) based on the lectures and try to write a report. Students are required to submit a report for task in classes.
|
| ６． |
Note |
|
Students have to prepare and bring a Textbook, note, a triangle(set square) and drawing compass and scientific electronic calculator in the class.
The Exchange report of reflection is carried out in every class in this course, in order to communicate with teacher.
This course will be taught in Japanese.
|
| ７． |
Schedule |
|
１.
Basic of Mechanical Design
|
２.
Strength and Rigidity of Material
|
３.
Accuracy of Machine
|
４.
Design of Screw |
５.
Group Work and Presentation
|
６.
Design of Shaft
|
７.
Group Work and Presentation
|
８.
Design of Bearing
|
９.
Group Work and Presentation
|
10.
Design of Gear
|
11.
Group Work and Presentation
|
12.
Design of Spring
|
13.
Group Work and Presentation
|
14.
Exercise of Task 1 : Group Work
|
15.
Exercise of Task 2 : Group Work
|
|
| １． |
Outline |
|
Understanding of Design and Drawing is deepened by studying and learning the basics of machine design, strength and stiffness of materials, and accuracy and precision of machines. Students will learn the design skills and methods for five basic machine elements, namely, screw, shaft, bearing, gear and spring, and exercise designing of them. By the end of the course, the design calculation and design drawings for the above five elements will be completed. In this course, and students perform a group work and students make a presentation of their solution for task in front of other students. Students can acquire the knowledge, skill and behavior for DP2 to DP4.
|
| ２． |
Objectives |
|
It's so important to have skill and knowledge of basic Design and Drawing if one is to pursue a career in Product Engineering (MONOZUKURI).
In this course, students will learn the basic design of machines, design concepts, material strength and stiffness, machine accuracy and precision, and international standards for machines. Another purpose of this course is to learn the design and drawing methods for five element components of machine, namely, screw, shaft, bearing, gear and spring. Objective of this course is acquiring the fundamental knowledge and skills for the Design and Drawing for Product Engineering. And students will have a presentation skill through this course. So, students can discuss about drawings based on their learning of this course.
|
| ３． |
Grading Policy |
|
Your final grade will be calculated according to the following process : Reports for tasks(30%) and submission of the calumniation report and drawings for final task(70%) on 14th & 15th classes. And students are required to attend classes over 2/3 of total classes in this course, in order to take part in the term-end examination.
|
| ４． |
Textbook and Reference |
|
Textbook:『Mechanical Design Method(the third Edition)』：Tadao Tsukada ;Morikita Pablishing Co., Ltd.
Reference book:『Main Theory Mechanical Drawing』：Kiyoshi Onishi;Ohmusha Pablishing Co., Ltd.
『Basic of Mechanical Design and Drawing(the second Edition)』; Surikogaku Pablishing Co., Ltd.
|
| ５． |
Requirements (Assignments) |
|
Students should study(1hr) watching and reading textbook and documents by LMS and they also should review(2hr) based on the lectures and try to write a report. Students are required to submit a report for task in classes.
|
| ６． |
Note |
|
Students have to prepare and bring a Textbook, note, a triangle(set square) and drawing compass and scientific electronic calculator in the class.
The Exchange report of reflection is carried out in every class in this course, in order to communicate with teacher.
This course will be taught in Japanese.
|
| ７． |
Schedule |
|
１.
Basic of Mechanical Design
|
２.
Strength and Rigidity of Material
|
３.
Accuracy of Machine
|
４.
Design of Screw |
５.
Group Work and Presentation
|
６.
Design of Shaft
|
７.
Group Work and Presentation
|
８.
Design of Bearing
|
９.
Group Work and Presentation
|
10.
Design of Gear
|
11.
Group Work and Presentation
|
12.
Design of Spring
|
13.
Group Work and Presentation
|
14.
Exercise of Task 1 : Group Work
|
15.
Exercise of Task 2 : Group Work
|
|
|